Molecule [DS] Driveway Sealer


Print


  1. Safety Information

    Personal protective equipment (PPE) is recommended for application:
    ○ Gloves 2
    ○ Safety glasses




  2. Coverage Rates for Molecule [DS] Driveway Sealer

    Concrete (standard or embellished) - 300 Ft2 / Gallon (7.3 m2/ litre)
    Porous pavers & natural stone - 300 Ft2 / Gallon (7.3 m2/ litre)
    Dense pavers & natural stone - 400 Ft2 / Gallon (9.8 m2/ litre)




  3. Recommended Tools

    Handheld or backpack pump sprayer (25-45 PSI/ 1.7-2.75 bar)
    Foam rubber squeegee w/ broom handle extension
    Optional
    3/8” nap paint roller (1 cm)
    Foam paint brush
    Grout sponge




  4. Suitable Applications / Materials


    APPLICATIONS
    ➢ Driveways
    ➢ Parking areas
    ➢ Garage / Shop floors
    ➢ Patios
    ➢ Walkways

    SURFACE MATERIALS
    ➢ Concrete (standard or embellished)
    ➢ Pavers
    ➢ Natural stone
    ➢ Bricks




  5. Top 5 Tips for Molecule [DS] Driveway Sealer

    ➢ Molecule [DS] should be installed within an ambient and surface temperature range of 40º- 90º F (4.4-32.2 C). Shaded, low sunlight, or colder areas will lengthen cure times. Conversely, direct sun, warmer areas will shorten cure times. Avoid temperatures at or below freezing or above 100º F (0-38 C) for application, curing phase, or storage.
    ➢ Molecule [DS] is a water-based, fluoropolymer, penetrating sealer. The curing phase is dependent upon complete evaporation of the water component (usually 4-12 hours in optimal) daytime conditions).
    ➢ Apply Molecule [DS] in one single application coat. Do not divide recommended application rates into multiple coats. Always consult manufacturer coverage rate guidelines, or contact our Technical Support desk by phone 877-356-2250, or by email Info@TechniSoil.com.
    ➢ Do not apply Molecule [DS] within a minimum of 24 hours before or after rainfall. In excessively wet conditions, allow project area to dry completely before application.
    ➢ Clean driveway thoroughly before applying. Molecule [DS] should not be applied over the top of other sealers, stains, efflorescence, or dirt as it may affect adhesion, cure, & finished aesthetic.




  6. Preparation

    ➢ Always perform a test section using recommended installation methods to confirm suitability of materials and project conditions!
    ➢ Remove all existing sealers, stains, dirt, efflorescence, & debris with environmentally safe cleaning agent before applying Molecule [DS].
    ➢Surface must be completely clean and dry before application.
    ➢ Do not apply in wet conditions. Plan a minimum 24 hour time window free of rainfall for application and curing phase.
    ➢ Coverage rates may vary based on surface porosity, and joint width, depth, & material.
    ➢ Keep project area free from any moisture such as rain or irrigation sprinklers, vehicular traffic, or otherwise until fully cured (4-12 hours in optimal daytime conditions).




  7. Installation of Molecule [DS] Driveway Sealer

    ➢ For best results, thoroughly remove any residual sand, dust or aggregates from the surface using a leaf blower or broom before applying Molecule [DS].
    ➢ Mask or shield any adjacent surfaces in case of overspray or accidental application.
    ➢ Pour contents of Molecule [DS] bottle into a 1-5 gallon (3.8-19 litre) capacity handheld or backpack pump sprayer.
    ➢ Carefully plan application process to avoid under or over application and ‘painting into a corner’.
    ➢ Visually map out sections of application area according to recommended coverage rate to ensure proper coverage.
    ○ TIP: If the recommended coverage rate is 400 ft2/gallon, measure an area that matches 400 ft2 (20’ x 20’ for example) and set a small indicating marker at the beginning and end of the section. Ensure 1 gallon of sealer has been evenly distributed over the section.
    ➢ Spray Molecule [DS] evenly over surface using a side-to-side motion. Avoid puddling or significant runoff of sealer.
    ➢ Sealer will have a muted white hue initially which quickly dissipates and turns clear.
    IMPORTANT! Before sealer fully penetrates and/or turns clear, use foam rubber squeegee to evenly distribute over the application surface.
    ➢ A 3/8” (1 cm) nap roller, grout sponge, or foam paint brush may be used to apply sealer in hard to reach places.
    ➢ During application, avoid foaming sealer. If foaming occurs, distribute the liquid evenly using a squeegee or sponge.
    IMPORTANT! Do not divide recommended application rates into multiple coats. Always consult manufacturer coverage rate guidelines or contact technical support at: 877-356-2250.




  8. Cure Times for Molecule [DS] Driveway Sealer

    Keep treated project areas free of any moisture such as rain or irrigation sprinklers, foot traffic, or otherwise until fully cured (usually 4-12 hours in optimal conditions).




  9. Cleanup

    Clean all tools immediately after use by simply rinsing tools with water and a soft bristle brush. In case of accidental sealer spill onto tools, equipment, or adjacent surfaces, clean immediately with soap and water as needed. For dried sealer, use a 1:1 acetone / water mixture and a brush to scrub affected areas. Use caution, acetone will remove paint from surfaces.




  10. Storage of Molecule [DS] Driveway Sealer

    Store unused Molecule [DS] with lid secured indoors and out of direct sunlight in a temperature range of 40º-90º F (4.4-32.2 C). Do not allow material to freeze




  11. Maintenance

    For periodic maintenance of surface sealed with Molecule [DS], use Molecule [HS] Hardscape Shampoo to clean and bolster the protectant coating.
    Molecule [DS] maintenance coats can be applied at the recommended application rates at any time, usually 6-24 months after initial application




  12. Warranty

    TechniSoil Global, Inc. warrants this product to be free from defects. Where permitted by law, TechniSoil makes no other warranties with respect to this product, express or implied, including without limitation the implied warranties of merchantability or fitness for particular purpose. The purchaser shall be responsible to orchestrate their own tests to determine the suitability of this product for their particular purpose. TechniSoil's liability shall be limited in all events to supplying sufficient product to re-treat the specific areas to which product proven to be defective has been applied. Acceptance and use of this product absolves TechniSoil from any other liability, from any and all sources, including liability for incidental, consequential or resultant damages whether due to breach of warranty, negligence or strict liability. This warranty may not be modified or extended by representatives of TechniSoil, its distributors or dealers, independent contractors, clients or end-users of any kind.