Molecule [DS] Driveway Sealer
: Molecule [DS] Driveway Sealer
Recommended use of the chemical and restrictions on use
Identified uses: Coatings product
TechniSoil Global, Inc.
5660 Westside Road
Redding, CA, USA 96001
Customer Information Number
Toll Free: 877-356-2250
EMERGENCY TELEPHONE NUMBER
24-Hour Emergency Contact: 800-424-9300
Local Emergency Contact: 800-424-9300
Skin sensitisation - Not Classified
Carcinogenicity - Not Classified
Signal word: None
Hazardous decomposition products including hydrogen fluoride and other toxic fluorinated compounds may be formed at high temperatures and during combustion. Inhalation of these compounds may result in serious lung irritation. Excessive exposure could result in delayed pulmonary edema in some cases, and on very high exposure, damage to the liver and kidneys.
COMPOSITION / INFORMATION ON INGREDIENTS
Polymers, water based. This product is a mixture
Proprietary Polymer Blend
5 - 25%
75 - 95%
FIRST AID MEASURES
Description of first aid measures
Move person to fresh air; if effects occur, consult a physician.
Remove material from skin immediately by washing with soap and plenty of water. Remove contaminated clothing and shoes while washing. Seek medical attention if irritation persists. Wash clothing before reuse. Discard items which cannot be decontaminated, including leather articles such as shoes, belts and watchbands.
Flush eyes thoroughly with water for several minutes. Remove contact lenses after the initial 1-2 minutes and continue flushing for several additional minutes. If effects occur, consult a physician, preferably an ophthalmologist.
Consult a doctor immediately.
Most important symptoms and effects, both acute and delayed:
Aside from the information found under Description of first aid measures (above) and Indication of immediate medical attention and special treatment needed (below), any additional important symptoms and effects are described in Section 11: Toxicology Information.
Indication of any immediate medical attention and special treatment needed
Notes to physician:
No specific antidote. Treatment of exposure should be directed at the control of symptoms and the clinical condition of the patient.
Suitable extinguishing media:
Use extinguishing media appropriate for surrounding fire.
Unsuitable extinguishing media:
No data available
Special hazards arising from the substance or mixture
Hazardous combustion products:
Formation of toxic gases including hydrofluoric acid, perfluoroisobutylene, and carbonyl fluoride is possible during heating or in case of fire.
Unusual Fire and Explosion Hazards:
Material can splatter above 100Â°C/212Â°F. Dried product can burn.
Advice for firefighters
Fire Fighting Procedures:
No data available.
Special protective equipment for firefighters:
Use NIOSH/MSHA approved SCBA and bunker gear. Evolution of acidic gases may require complete wash down of protective clothing prior to removal.
ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures:
Ensure cleanup is done only by trained personnel wearing appropriate personal protective equipment. Ventilate area and cover with absorbent material. Collect spilled material in a container and seal. Spilled material is a slipping hazard.
Environmental precautions: CAUTION:
Keep spills and cleaning runoff out of municipal sewers and open bodies of water.
Methods and materials for containment and cleaning up:
Contain spills immediately with inert materials (e.g., sand, earth). Transfer liquids and solid diking material to separate suitable containers for recovery or disposal.
HANDLING AND STORAGE
Precautions for safe handling:
Follow safe industrial hygiene practices and wear proper protective equipment. Use only in well ventilated areas. Wash hands thoroughly after handling. Wash clothing after use. Avoid contact with skin or eyes. Do not breathe vapor or spray. Do not store or consume food, drink or tobacco in areas where they may become contaminated with this material.
If smoking tobacco becomes contaminated by this material, exposure to toxic gases through inhalation can occur. Therefore, do not smoke in the work areas and wash hands and face after handling in order to avoid transfer of material onto tobacco.
Store material at -5Â°C (23Â°F) to 30Â°C (86Â°F).
Keep away from heat, steam, sunlight, sparks and open flame. Store containers tightly closed when not in use.
EXPOSURE CONTROLS / PERSONAL PROTECTION
No exposure limits available for this product. Excessive exposure to thermal degradation products could result in delayed pulmonary edema in some cases, and on very high exposure, damage to the liver and kidneys. These substances may include: perfluoroisobutylene (TLV = 0.01 ppm Ceiling), carbonyl fluoride (TLV = 2 ppm TWA, 5 ppm STEL), hydrogen fluoride (TLV = 2 ppm Ceiling, 0.5 ppm TWA).
Use local exhaust ventilation if material is heated above 200Â°C
Individual protection measures
Use safety glasses (with side shields).
Chemical resistant gloves and protective clothing should be worn when handling this material.
Use protective clothing chemically resistant to this material. Selection of specific items such as face shield, boots, apron, or full body suit will depend on the task. Eyewash station and safety shower.
Use respirator suitable for protection when spraying this material. If material is heated above 200Â°C, use a positive pressure air supplied respirator or SCBA.
PHYSICAL AND CHEMICAL PROPERTIES
Physical state Liquid
Color Off white/pale-yellowish
Odor Slightly sweet
Odor Threshold No data available
Melting point/range Not Applicable
Freezing point Approximately 0Â°C
Boiling point (760 mmHg) Approximately 100 Â°C Water
Flash point > 200Â°F (Closed Cup), > 209Â°F (Open Cup)
Evaporation Rate (Butyl Acetate = 1) Not available
Flammability (solid, gas) Not available
Lower explosion limit Not available
Upper explosion limit Not available
Vapor Pressure Not available
Relative Vapor Density (air = 1) Not available
Relative Density (water = 1) 1.0-1.2
Water solubility Miscible in water
Partition coefficient: n- octanol/water No data available
Auto-ignition temperature Not applicable
Decomposition temperature No data available
Dynamic Viscosity No data available
Kinematic Viscosity No data available
Explosive properties No data available
Oxidizing properties No data available
Molecular weight No data available
Percent volatility No data available
NOTE: The physical data presented above are typical values and should not be construed as a specification.
STABILITY AND REACTIVITY
No data available
Possibility of hazardous reactions:
Product will not undergo polymerization.
Conditions to avoid:
Keep away from heat, sparks, flame, high temperature
May react with metals, such as sodium, magnesium, aluminum at elevated temperatures (above 425 C); may react upon prolonged exposure to fluorine or in oxygen-fluorine mixtures at high temperatures and pressures. Contact with incompatible materials may result in fire or explosion.
Hazardous decomposition products:
Decomposition or by-products and toxic by-products including hydrofluoric acid, perfluoroisobutylene, and carbonyl fluoride may be formed at very high temperatures.
Acute oral toxicity
May be harmful if swallowed
For this family of materials:
LD50, Rat, > 2,000 mg/kg
Acute dermal toxicity
May cause skin irritation
Acute inhalation toxicity
May cause respiratory irritation
May cause skin irritation
Skin Irritation by Draize (rabbit): Non-irritating
Serious eye damage/eye irritation
May cause mild irritation
Eye Irritation by Kay and Calandra (rabbit): Mildly irritating
Skin by Local Lymph Node Assay (mouse): Negative
Specific Target Organ Systemic Toxicity (Single Exposure)
Evaluation of available data suggests that this material is not an STOT-SE toxicant.
Specific Target Organ Systemic Toxicity (Repeated Exposure)
No relevant data found.
None of the components in this material are listed by NTP, OSHA or IARC.
No relevant data found.
No relevant data found.
For this family of materials: In vitro genetic toxicity studies were negative.
Based on physical properties, not likely to be an aspiration hazard.
Persistence and degradability
Comply with Federal, State and Local regulations concerning health and environment when disposing of
Classification for SEA transport (IMO-IMDG):
EINECS 1987 List
Fluoroalkyl methacrylate is registered by the listing of its constituent monomers.
United States TSCA Inventory (TSCA)
All components of this product are in compliance with the inventory listing requirements of the U.S. Toxic Substance Control Act (TSCA) Chemical Substance Inventory. The base polymer is subject to export notification under Section 12(b) of TSCA.
The fluoropolymer of this product is listed on the chemical inventories of the following countries: Japan, Korea, Taiwan, and Switzerland.
China: Not Listed
State and local regulations may have specific requirements for this product or components of this product; consult specific state and local regulatory requirements for additional information.
For additional information, refer to the American Conference of Governmental Industrial Hygienists (ACGIH) documentation of TLVâ€™s (Threshold Limit Values) for individual components, Fluoropolymers Safe Handling Guide published by The Society of the Plastics Industry, and the DOT Emergency Response Guidebook.
The product is for the industrial use only. We do not guarantee the safety in case the product is used for the other purposes. When using the product for healthcare application or food/feed application, consult us in advance.
This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.
TechniSoil Global Inc. urges each customer or recipient of this (M)SDS to study it carefully and consult appropriate expertise, as necessary or appropriate, to become aware of and understand the data contained in this (M)SDS and any hazards associated with the product. The information herein is provided in good faith and believed to be accurate as of the effective date shown above. However, no warranty, express or implied, is given. Regulatory requirements are subject to change and may differ between various locations. It is the buyer's/user's responsibility to ensure that his activities comply with all federal, state, provincial or local laws. The information presented here pertains only to the product as shipped. Since conditions for use of the product are not under the control of the manufacturer, it is the buyer's/user's duty to determine the conditions necessary for the safe use of this product. Due to the proliferation of sources for information such as manufacturer- specific (M)SDSs, we are not and cannot be responsible for (M)SDSs obtained from any source other than ourselves. If you have obtained an (M)SDS from another source or if you are not sure that the (M)SDS you have is current, please contact us for the most current version.
TechniSoil Global Inc. encourages and expects you to read and understand the entire (M)SDS, as there is important information throughout the document. We expect you to follow the precautions identified in this document unless your use conditions would necessitate other appropriate methods or actions.